The Stand 21 Featherlite 20 Head and Neck Restraint.
The side of the Stand 21 Featherlite 20 Head and Neck Restraint.
The back of the Stand 21 Featherlite 20 Head and Neck Restraint close up.
The Stand 21 Featherlite 20 Head and Neck Restraint at an angle.
The Stand 21 Featherlite 20 Head and Neck Restraint from the back.

Stand 21 Featherlite 20 Head and Neck Restraint

$2,215.00
By Stand 21
SKU: SPFHRFL20-LRG
Size
5 in stock, ready to ship

Experience elite-level protection with the Stand 21 Featherlite 20 Head and Neck Restraint. Weighing an ultra-light ~310g (without padding), this advanced carbon-composite device is engineered for exceptional ergonomic performance, significantly minimizing interference with the seat and helmet. Fully certified to both FIA 8858-2010 and SFI 38.1 standards, it delivers world-class safety for uncompromising drivers. The 20-degree angle is specifically tailored for upright seating positions, making it the premier choice for sports cars, sedans, and club racers seeking track-ready defense without the added bulk.

Features

• FIA 8858-2010 homologated and manufacturer certified to SFI 38.1.
• High-strength carbon composition.
• Lightweight – weighs only 310 grams.
• New and even more exceptional ergonomics definition of legs for comfort.
• Revolutionary self-centering, free-floating single tether for maximum mobility.
• Unprecedented curvature beam facilitating the absence of discomfort between the helmet and the seat/headrest
• Available in Medium or Large with a 20° Angle for use with most seats/setups.
• Compatible with Hans spring-post anchors (Not included), and spring-post anchors that come pre-installed on FIA 8858-2015 helmets.
• Supplied with black padding, sliding tether, and protective bag.
Technical Details

• Rating: FIA 8858-2010 & SFI 38.1
• Part Number: SPFHRFL20
• Manufacturer: SHR20MFEATH, SHR20LFEATH
HANS Installation Instructions

Most modern Snell SA2015 and later and/or FIA8858/FIA8860/FIA8859 helmets have threaded mounting posts bonded into the helmet shell. This allows for very quick and easy installation without the need for specialty tools or helmet modification. If your helmet does not have these threaded mounting points, please get in touch with us for assistance.

Tools needed for installation:

  • 5/32 or 4mm Allen Key (put down your impact gun - either size will fit)
  • Hans Anchor Key/Wrench (not included) OR Hans Tether attached to your device

Instructions:

  1. Using the entire anchor, thread it onto the terminal on the helmet. Note that threadlocker has been pre-applied to the anchor's thread. If transferring the anchor to a new helmet, fresh threadlocker is recommended.
  2. Hand-tighten the screw until snug, making sure the point on the anchor faces rearward. When installing Quick-Click-style anchors, the opening hasp should point rearward. (Click here for sample image)
  3. Tighten the screw a ¼ turn past snug. You may need to hold the anchor still while tightening to ensure the point on the anchor remains facing rearward. This can be accomplished with the flat edge of a connected tether or using the specialty Hans Anchor Key (or similar flat spanner wrench). Note: Not a lot of force is needed to tighten this screw - if you are having problems keeping the point on the anchor in place, you're probably over-tightening! Overtightening can easily break the bonded anchor terminal and/or otherwise damage your helmet!
  4. Test your installation by connecting the Hans tether to the anchor and makeing sure it slides on/off with little resistance. If the anchor is installed too tightly, it will feel tight.
  5. That's it!
View details